Manual placa gme rev-03_a v12
Dating > Manual placa gme rev-03_a v12
Download links: → Manual placa gme rev-03_a v12 → Manual placa gme rev-03_a v12
The processor socket comes with a screw to secure the processor, please unlock the screw first. Essa placa costuma ter várias peças em curto, possivelmente pelo relato de ter caído agua, já viu se o SIO esquenta? Hola amigo, resulta que tuve un problema con una tablet BU con virus;, son ensambladas en Colombia pero con partes chinas... This port connects a tape, CD, DVD player, or other audio sources. Take one of the marked corner with gold triangle on the CPU. S3 Graphics UniChrome integrada de gráficos con 8 a 64 MB de memoria compartida proporciona suficiente energía para aplicaciones de oficina y el hogar.
When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device. Alternatively, please try the following help resources for further guidance. Product Product introduction introduction... Unplug the power cord from the wall socket before touching any component. Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity Hold components by the edges to avoid touching the ICs on... Refer to the chassis documentation before installing the motherboard. Make sure to unplug the power cord before installing or removing the motherboard. Take one of the marked corner with gold triangle on the CPU. Before installing the CPU, make sure that the socket box is facing towards you. The processor socket comes with a screw to secure the processor, please unlock the screw first. Turn the screw to the lock position. Install the motherboard to the chassis before you install the CPU fan and heatsink assembly. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components, and hardware monitoring errors can occur if you fail to plug this connector. Rotate each fastener counterclockwise. Pull up four fasteners to disengage the heatsink and fan assembly from the motherboard. Carefully remove the heatsink and fan assembly from the motherboard. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM. Installing DDR2 DIMM other than the recommended configurations may cause memory sizing error or system boot failure. Failure to do so may cause severe damage to both the motherboard and the components. Unlock a DIMM socket by pressing the... Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. This port connects a tape, CD, DVD player, or other audio sources. AUDIO1 Line-Out port Lime This port connects a headphone or a speaker. In 4-channel, 6-channel, and 8-channel configuration, the function of this port becomes Front Speaker Out. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. Important notes on the Motherboard Power Requirements Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead... Insufficient air flow inside the system may damage the motherboard components, and hardware monitoring errors can occur if you fail to plug this connector. System Power LED 2-pin PWRLED This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. When using the connectors in Standard IDE mode, connect the primary boot hard disk drive to the SATA1 connector. These USB connectors comply with USB 2.
Last updated
